moby--moby/docs/cluster_volumes.md

Cluster Volumes

Docker Cluster Volumes is a new feature which allows using CSI plugins to create cluster-aware volumes

Installing a CSI plugin

CSI, the Container Storage Interface, defines an API for storage providers to write storage plugins which are cross-compatible between various container orchestrators. However, most CSI plugins are shipped with configuration specific to Kubernetes. Docker CSI Plugins use the same binaries as those for Kubernetes, but in a different environment and sometimes with different configuration.

If a plugin is already adapted for and available for Docker, it can be installed through the docker plugin install command. Though such plugins may require configuration specific to the user's environment, they will ultimately be detected by and work automatically with Docker once enabled.

Currently, there is no way to automatically deploy a Docker Plugin across all nodes in a cluster. Therefore, users must ensure the Docker Plugin is installed on all nodes in the cluster on which it is desired.

Docker Swarm worker nodes report their active plugins to the Docker Swarm managers, and so it is not necessary to install a plugin on every worker node if this is not desired. However, the plugin must be installed on every manager node, or a leadership change could result in Docker Swarm no longer having the ability to call the plugin.

Creating a Docker CSI Plugin

Before following this section, readers should ensure they are acquainted with the Docker Engine managed plugin system. Docker CSI plugins use this system to run.

Docker CSI plugins are identified with a special interface type. There are two related interfaces that CSI plugins can expose. In the config.json, this should be set as such.

  "interface": {
    "types": ["docker.csicontroller/1.0","docker.csinode/1.0"]
  }

Additionally, the CSI specification states that CSI plugins should have CAP_SYS_ADMIN privileges, so this should be set in the config.json as well:

  "linux" : {
    "capabilities": ["CAP_SYS_ADMIN"]
  }

Other configuration is largely specific to the CSI plugin.

Split-Component Plugins

For split-component plugins, users can specify either the docker.csicontroller/1.0 or docker.csinode/1.0 plugin interfaces. Manager nodes should run plugin instances with the docker.csicontroller/1.0 interface, and worker nodes the docker.csinode/1.0 interface.

Docker does support running two plugins with the same name, nor does it support specifying different drivers for the node and controller plugins. This means in a fully split plugin, Swarm will be unable to schedule volumes to manager nodes.

If it is desired to run a split-component plugin such that the Volumes managed by that plugin are accessible to Tasks on the manager node, the user will need to build the plugin such that some proxy or multiplexer provides the illusion of combined components to the manager through one socket, and ensure the plugin reports both interface types.

Using Cluster Volumes

Create a Cluster Volume

Creating a Cluster Volume is done with the same docker volume commands as any other Volume. To create a Cluster Volume, one needs to do both of things:

• Specify a CSI-capable driver with the --driver or -d option.
• Use any one of the cluster-specific docker volume create flags.

For example, to create a Cluster Volume called my-volume with the democratic-csi Volume Driver, one might use this command:

docker volume create \
  --driver democratic-csi \
  --type mount \
  --sharing all \
  --scope multi \
  --limit-bytes 10G \
  --required-bytes 1G \
  my-volume

List Cluster Volumes

Cluster Volumes will be listed along with other volumes when doing docker volume ls. However, if users want to see only Cluster Volumes, and with cluster-specific information, the flag --cluster can be specified:

$ docker volume ls --cluster
VOLUME NAME   GROUP     DRIVER    AVAILABILITY   STATUS
volume1       group1    driver1   active         pending creation
volume2       group1    driver1   pause          created
volume3       group2    driver2   active         in use (1 node)
volume4       group2    driver2   active         in use (2 nodes)

Deploying a Service

Cluster Volumes are only compatible with Docker Services, not plain Docker Containers.

In Docker Services, a Cluster Volume is used the same way any other volume would be used. The type should be set to csi. For example, to create a Service that uses my-volume created above, one would execute a command like:

docker service create \
  --name my-service \
  --mount type=csi,src=my-volume,dst=/srv/www \
  nginx:alpine

When scheduling Services which use Cluster Volumes, Docker Swarm uses the volume's information and state to make decisions about Task placement.

For example, the Service will be constrained to run only on nodes on which the volume is available. If the volume is configured with scope=single, meaning it can only be used on one node in the cluster at a time, then all Tasks for that Service will be scheduled to that same node. If that node changes for some reason, like a node failure, then the Tasks will be rescheduled to the new node automatically, without user input.

If the Cluster Volume is accessible only on some set of nodes at the same time, and not the whole cluster, then Docker Swarm will only schedule the Service to those nodes as reported by the plugin.

Using Volume Groups

It is frequently desirable that a Service use any available volume out of an interchangeable set. To accomplish this in the most simple and straightforward manner possible, Cluster Volumes use the concept of a volume "Group".

The Volume Group is a field, somewhat like a special label, which is used to instruct Swarm that a given volume is interchangeable with every other volume of the same Group. When creating a Cluster Volume, the Group can be specified by using the --group flag.

To use a Cluster Volume by Group instead of by Name, the mount src option is prefixed with group:, followed by the group name. For example:

--mount type=csi,src=group:my-group,dst=/srv/www

This instructs Docker Swarm that any Volume with the Group my-group can be used to satisfy the mounts.

Volumes in a Group do not need to be identical, but they must be interchangeable. These caveats should be kept in mind when using Groups:

• No Service ever gets the monopoly on a Cluster Volume. If several Services use the same Group, then the Cluster Volumes in that Group can be used with any of those Services at any time. Just because a particular Volume was used by a particular Service at one point does not mean it won't be used by a different Service later.
• Volumes in a group can have different configurations, but all of those configurations must be compatible with the Service. For example, if some of the Volumes in a group have sharing=readonly, then the Service must be capable of using the volume in read-only mode.
• Volumes in a Group are created statically ahead of time, not dynamically as-needed. This means that the user must ensure a sufficient number of Volumes belong to the desired Group to support the needs of the Service.

Taking Cluster Volumes Offline

For various reasons, users may wish to take a particular Cluster Volume offline, such that is not actively used by Services. To facilitate this, Cluster Volumes have an availability option similar to Docker Swarm nodes.

Cluster Volume availability can be one of three states:

• active - Default. Volume can be used as normal.
• pause - The volume will not be used for new Services, but existing Tasks using the volume will not be stopped.
• drain - The volume will not be used for new Services, and any running Tasks using the volume will be stopped and rescheduled.

A Volume can only be removed from the cluster entirely if its availability is set to drain, and it has been fully unpublished from all nodes.

Force-Removing Volumes

There are cases where a Volume can get caught in a state where Swarm cannot verify their removal. In these cases,

Unsupported Features

The CSI Spec allows for a large number of features which Cluster Volumes in this initial implementation do not support. Most notably, Cluster Volumes do not support snapshots, cloning, or volume expansion.