83 KiB
reading_time | stage | group | info |
---|---|---|---|
true | Enablement | Distribution | To determine the technical writer assigned to the Stage/Group associated with this page, see https://about.gitlab.com/handbook/engineering/ux/technical-writing/#designated-technical-writers |
Reference architecture: up to 50,000 users (PREMIUM ONLY)
This page describes GitLab reference architecture for up to 50,000 users. For a full list of reference architectures, see Available reference architectures.
- Supported users (approximate): 50,000
- High Availability: Yes
- Test requests per second (RPS) rates: API: 1000 RPS, Web: 100 RPS, Git: 100 RPS
Service | Nodes | Configuration | GCP | AWS | Azure |
---|---|---|---|---|---|
External load balancing node | 1 | 8 vCPU, 7.2 GB memory | n1-highcpu-8 | c5.2xlarge | F8s v2 |
Consul | 3 | 2 vCPU, 1.8 GB memory | n1-highcpu-2 | c5.large | F2s v2 |
PostgreSQL | 3 | 16 vCPU, 60 GB memory | n1-standard-16 | m5.4xlarge | D16s v3 |
PgBouncer | 3 | 2 vCPU, 1.8 GB memory | n1-highcpu-2 | c5.large | F2s v2 |
Internal load balancing node | 1 | 8 vCPU, 7.2 GB memory | n1-highcpu-8 | c5.2xlarge | F8s v2 |
Redis - Cache | 3 | 4 vCPU, 15 GB memory | n1-standard-4 | m5.xlarge | D4s v3 |
Redis - Queues / Shared State | 3 | 4 vCPU, 15 GB memory | n1-standard-4 | m5.xlarge | D4s v3 |
Redis Sentinel - Cache | 3 | 1 vCPU, 1.7 GB memory | g1-small | t2.small | B1MS |
Redis Sentinel - Queues / Shared State | 3 | 1 vCPU, 1.7 GB memory | g1-small | t2.small | B1MS |
Gitaly | 2 (minimum) | 64 vCPU, 240 GB memory | n1-standard-64 | m5.16xlarge | D64s v3 |
Sidekiq | 4 | 4 vCPU, 15 GB memory | n1-standard-4 | m5.xlarge | D4s v3 |
GitLab Rails | 12 | 32 vCPU, 28.8 GB memory | n1-highcpu-32 | c5.9xlarge | F32s v2 |
Monitoring node | 1 | 4 vCPU, 3.6 GB memory | n1-highcpu-4 | c5.xlarge | F4s v2 |
Object storage | n/a | n/a | n/a | n/a | n/a |
NFS server | 1 | 4 vCPU, 3.6 GB memory | n1-highcpu-4 | c5.xlarge | F4s v2 |
The Google Cloud Platform (GCP) architectures were built and tested using the Intel Xeon E5 v3 (Haswell) CPU platform. On different hardware you may find that adjustments, either lower or higher, are required for your CPU or node counts. For more information, see our Sysbench-based CPU benchmark.
Due to better performance and availability, for data objects (such as LFS, uploads, or artifacts), using an object storage service is recommended instead of using NFS. Using an object storage service also doesn't require you to provision and maintain a node.
Setup components
To set up GitLab and its components to accommodate up to 50,000 users:
- Configure the external load balancing node to handle the load balancing of the GitLab application services nodes.
- Configure Consul.
- Configure PostgreSQL, the database for GitLab.
- Configure PgBouncer.
- Configure the internal load balancing node.
- Configure Redis.
- Configure Gitaly, which provides access to the Git repositories.
- Configure Sidekiq.
- Configure the main GitLab Rails application to run Puma/Unicorn, Workhorse, GitLab Shell, and to serve all frontend requests (which include UI, API, and Git over HTTP/SSH).
- Configure Prometheus to monitor your GitLab environment.
- Configure the object storage used for shared data objects.
- Configure Advanced Search (optional) for faster, more advanced code search across your entire GitLab instance.
- Configure NFS (optional, and not recommended) to have shared disk storage service as an alternative to Gitaly or object storage. You can skip this step if you're not using GitLab Pages (which requires NFS).
The servers start on the same 10.6.0.0/24 private network range, and can connect to each other freely on these addresses.
The following list includes descriptions of each server and its assigned IP:
10.6.0.10
: External Load Balancer10.6.0.11
: Consul 110.6.0.12
: Consul 210.6.0.13
: Consul 310.6.0.21
: PostgreSQL primary10.6.0.22
: PostgreSQL secondary 110.6.0.23
: PostgreSQL secondary 210.6.0.31
: PgBouncer 110.6.0.32
: PgBouncer 210.6.0.33
: PgBouncer 310.6.0.40
: Internal Load Balancer10.6.0.51
: Redis - Cache Primary10.6.0.52
: Redis - Cache Replica 110.6.0.53
: Redis - Cache Replica 210.6.0.71
: Sentinel - Cache 110.6.0.72
: Sentinel - Cache 210.6.0.73
: Sentinel - Cache 310.6.0.61
: Redis - Queues Primary10.6.0.62
: Redis - Queues Replica 110.6.0.63
: Redis - Queues Replica 210.6.0.81
: Sentinel - Queues 110.6.0.82
: Sentinel - Queues 210.6.0.83
: Sentinel - Queues 310.6.0.91
: Gitaly 110.6.0.92
: Gitaly 210.6.0.101
: Sidekiq 110.6.0.102
: Sidekiq 210.6.0.103
: Sidekiq 310.6.0.104
: Sidekiq 410.6.0.111
: GitLab application 110.6.0.112
: GitLab application 210.6.0.113
: GitLab application 310.6.0.121
: Prometheus
Configure the external load balancer
NOTE: Note: This architecture has been tested and validated with HAProxy as the load balancer. Although other load balancers with similar feature sets could also be used, those load balancers have not been validated.
In an active/active GitLab configuration, you will need a load balancer to route traffic to the application servers. The specifics on which load balancer to use or the exact configuration is beyond the scope of GitLab documentation. We hope that if you're managing multi-node systems like GitLab you have a load balancer of choice already. Some examples including HAProxy (open-source), F5 Big-IP LTM, and Citrix Net Scaler. This documentation will outline what ports and protocols you need to use with GitLab.
The next question is how you will handle SSL in your environment. There are several different options:
- The application node terminates SSL.
- The load balancer terminates SSL without backend SSL and communication is not secure between the load balancer and the application node.
- The load balancer terminates SSL with backend SSL and communication is secure between the load balancer and the application node.
Application node terminates SSL
Configure your load balancer to pass connections on port 443 as TCP
rather
than HTTP(S)
protocol. This will pass the connection to the application node's
NGINX service untouched. NGINX will have the SSL certificate and listen on port 443.
See the NGINX HTTPS documentation for details on managing SSL certificates and configuring NGINX.
Load balancer terminates SSL without backend SSL
Configure your load balancer to use the HTTP(S)
protocol rather than TCP
.
The load balancer will then be responsible for managing SSL certificates and
terminating SSL.
Since communication between the load balancer and GitLab will not be secure, there is some additional configuration needed. See the NGINX proxied SSL documentation for details.
Load balancer terminates SSL with backend SSL
Configure your load balancer(s) to use the 'HTTP(S)' protocol rather than 'TCP'. The load balancer(s) will be responsible for managing SSL certificates that end users will see.
Traffic will also be secure between the load balancer(s) and NGINX in this scenario. There is no need to add configuration for proxied SSL since the connection will be secure all the way. However, configuration will need to be added to GitLab to configure SSL certificates. See NGINX HTTPS documentation for details on managing SSL certificates and configuring NGINX.
Readiness checks
Ensure the external load balancer only routes to working services with built in monitoring endpoints. The readiness checks all require additional configuration on the nodes being checked, otherwise, the external load balancer will not be able to connect.
Ports
The basic ports to be used are shown in the table below.
LB Port | Backend Port | Protocol |
---|---|---|
80 | 80 | HTTP (1) |
443 | 443 | TCP or HTTPS (1) (2) |
22 | 22 | TCP |
- (1): Web terminal support requires
your load balancer to correctly handle WebSocket connections. When using
HTTP or HTTPS proxying, this means your load balancer must be configured
to pass through the
Connection
andUpgrade
hop-by-hop headers. See the web terminal integration guide for more details. - (2): When using HTTPS protocol for port 443, you will need to add an SSL certificate to the load balancers. If you wish to terminate SSL at the GitLab application server instead, use TCP protocol.
If you're using GitLab Pages with custom domain support you will need some
additional port configurations.
GitLab Pages requires a separate virtual IP address. Configure DNS to point the
pages_external_url
from /etc/gitlab/gitlab.rb
at the new virtual IP address. See the
GitLab Pages documentation for more information.
LB Port | Backend Port | Protocol |
---|---|---|
80 | Varies (1) | HTTP |
443 | Varies (1) | TCP (2) |
- (1): The backend port for GitLab Pages depends on the
gitlab_pages['external_http']
andgitlab_pages['external_https']
setting. See GitLab Pages documentation for more details. - (2): Port 443 for GitLab Pages should always use the TCP protocol. Users can configure custom domains with custom SSL, which would not be possible if SSL was terminated at the load balancer.
Alternate SSH Port
Some organizations have policies against opening SSH port 22. In this case, it may be helpful to configure an alternate SSH hostname that allows users to use SSH on port 443. An alternate SSH hostname will require a new virtual IP address compared to the other GitLab HTTP configuration above.
Configure DNS for an alternate SSH hostname such as altssh.gitlab.example.com
.
LB Port | Backend Port | Protocol |
---|---|---|
443 | 22 | TCP |
Configure Consul
The following IPs will be used as an example:
10.6.0.11
: Consul 110.6.0.12
: Consul 210.6.0.13
: Consul 3
NOTE: Note:
The configuration processes for the other servers in your reference architecture will
use the /etc/gitlab/gitlab-secrets.json
file from your Consul server to connect
with the other servers.
To configure Consul:
-
SSH into the server that will host Consul.
-
Download/install the Omnibus GitLab Enterprise Edition package using steps 1 and 2 from the GitLab downloads page.
- Make sure you select the correct Omnibus package, with the same version the GitLab application is running.
- Do not complete any other steps on the download page.
-
Edit
/etc/gitlab/gitlab.rb
and add the contents:roles ['consul_role'] ## Enable service discovery for Prometheus consul['enable'] = true consul['monitoring_service_discovery'] = true ## The IPs of the Consul server nodes ## You can also use FQDNs and intermix them with IPs consul['configuration'] = { server: true, retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13), } # Set the network addresses that the exporters will listen on node_exporter['listen_address'] = '0.0.0.0:9100' # Disable auto migrations gitlab_rails['auto_migrate'] = false
-
Reconfigure Omnibus GitLab for the changes to take effect.
-
Go through the steps again for all the other Consul nodes, and make sure you set up the correct IPs.
NOTE: Note:
A Consul leader will be elected when the provisioning of the third Consul server is completed.
Viewing the Consul logs sudo gitlab-ctl tail consul
will display
...[INFO] consul: New leader elected: ...
You can list the current Consul members (server, client):
sudo /opt/gitlab/embedded/bin/consul members
You can verify the GitLab services are running:
sudo gitlab-ctl status
The output should be similar to the following:
run: consul: (pid 30074) 76834s; run: log: (pid 29740) 76844s
run: logrotate: (pid 30925) 3041s; run: log: (pid 29649) 76861s
run: node-exporter: (pid 30093) 76833s; run: log: (pid 29663) 76855s
Configure PostgreSQL
In this section, you'll be guided through configuring an external PostgreSQL database to be used with GitLab.
Provide your own PostgreSQL instance
If you're hosting GitLab on a cloud provider, you can optionally use a managed service for PostgreSQL. For example, AWS offers a managed Relational Database Service (RDS) that runs PostgreSQL.
If you use a cloud-managed service, or provide your own PostgreSQL:
- Set up PostgreSQL according to the database requirements document.
- Set up a
gitlab
username with a password of your choice. Thegitlab
user needs privileges to create thegitlabhq_production
database. - Configure the GitLab application servers with the appropriate details. This step is covered in Configuring the GitLab Rails application.
See Configure GitLab using an external PostgreSQL service for further configuration steps.
Standalone PostgreSQL using Omnibus GitLab
The following IPs will be used as an example:
10.6.0.21
: PostgreSQL primary10.6.0.22
: PostgreSQL secondary 110.6.0.23
: PostgreSQL secondary 2
First, make sure to install
the Linux GitLab package on each node. Following the steps,
install the necessary dependencies from step 1, and add the
GitLab package repository from step 2. When installing GitLab
in the second step, do not supply the EXTERNAL_URL
value.
PostgreSQL primary node
-
SSH into the PostgreSQL primary node.
-
Generate a password hash for the PostgreSQL username/password pair. This assumes you will use the default username of
gitlab
(recommended). The command will request a password and confirmation. Use the value that is output by this command in the next step as the value of<postgresql_password_hash>
:sudo gitlab-ctl pg-password-md5 gitlab
-
Generate a password hash for the PgBouncer username/password pair. This assumes you will use the default username of
pgbouncer
(recommended). The command will request a password and confirmation. Use the value that is output by this command in the next step as the value of<pgbouncer_password_hash>
:sudo gitlab-ctl pg-password-md5 pgbouncer
-
Generate a password hash for the Consul database username/password pair. This assumes you will use the default username of
gitlab-consul
(recommended). The command will request a password and confirmation. Use the value that is output by this command in the next step as the value of<consul_password_hash>
:sudo gitlab-ctl pg-password-md5 gitlab-consul
-
On the primary database node, edit
/etc/gitlab/gitlab.rb
replacing values noted in the# START user configuration
section:# Disable all components except PostgreSQL and Repmgr and Consul roles ['postgres_role'] # PostgreSQL configuration postgresql['listen_address'] = '0.0.0.0' postgresql['hot_standby'] = 'on' postgresql['wal_level'] = 'replica' postgresql['shared_preload_libraries'] = 'repmgr_funcs' # Disable automatic database migrations gitlab_rails['auto_migrate'] = false # Configure the Consul agent consul['services'] = %w(postgresql) # START user configuration # Please set the real values as explained in Required Information section # # Replace PGBOUNCER_PASSWORD_HASH with a generated md5 value postgresql['pgbouncer_user_password'] = '<pgbouncer_password_hash>' # Replace POSTGRESQL_PASSWORD_HASH with a generated md5 value postgresql['sql_user_password'] = '<postgresql_password_hash>' # Set `max_wal_senders` to one more than the number of database nodes in the cluster. # This is used to prevent replication from using up all of the # available database connections. postgresql['max_wal_senders'] = 4 postgresql['max_replication_slots'] = 4 # Replace XXX.XXX.XXX.XXX/YY with Network Address postgresql['trust_auth_cidr_addresses'] = %w(10.6.0.0/24) repmgr['trust_auth_cidr_addresses'] = %w(127.0.0.1/32 10.6.0.0/24) ## Enable service discovery for Prometheus consul['monitoring_service_discovery'] = true # Set the network addresses that the exporters will listen on for monitoring node_exporter['listen_address'] = '0.0.0.0:9100' postgres_exporter['listen_address'] = '0.0.0.0:9187' ## The IPs of the Consul server nodes ## You can also use FQDNs and intermix them with IPs consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13), } # # END user configuration
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure GitLab for the changes to take effect.
PostgreSQL secondary nodes
-
On both the secondary nodes, add the same configuration specified above for the primary node with an additional setting (
repmgr['master_on_initialization'] = false
) that will informgitlab-ctl
that they are standby nodes initially and there's no need to attempt to register them as a primary node:# Disable all components except PostgreSQL and Repmgr and Consul roles ['postgres_role'] # PostgreSQL configuration postgresql['listen_address'] = '0.0.0.0' postgresql['hot_standby'] = 'on' postgresql['wal_level'] = 'replica' postgresql['shared_preload_libraries'] = 'repmgr_funcs' # Disable automatic database migrations gitlab_rails['auto_migrate'] = false # Configure the Consul agent consul['services'] = %w(postgresql) # Specify if a node should attempt to be primary on initialization. repmgr['master_on_initialization'] = false # Replace PGBOUNCER_PASSWORD_HASH with a generated md5 value postgresql['pgbouncer_user_password'] = '<pgbouncer_password_hash>' # Replace POSTGRESQL_PASSWORD_HASH with a generated md5 value postgresql['sql_user_password'] = '<postgresql_password_hash>' # Set `max_wal_senders` to one more than the number of database nodes in the cluster. # This is used to prevent replication from using up all of the # available database connections. postgresql['max_wal_senders'] = 4 postgresql['max_replication_slots'] = 4 # Replace with your network addresses postgresql['trust_auth_cidr_addresses'] = %w(10.6.0.0/24) repmgr['trust_auth_cidr_addresses'] = %w(127.0.0.1/32 10.6.0.0/24) ## Enable service discovery for Prometheus consul['monitoring_service_discovery'] = true # Set the network addresses that the exporters will listen on for monitoring node_exporter['listen_address'] = '0.0.0.0:9100' postgres_exporter['listen_address'] = '0.0.0.0:9187' ## The IPs of the Consul server nodes ## You can also use FQDNs and intermix them with IPs consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13), }
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure GitLab for the changes to take effect.
Advanced configuration options are supported and can be added if needed.
PostgreSQL post-configuration
SSH into the primary node:
-
Open a database prompt:
gitlab-psql -d gitlabhq_production
-
Make sure the
pg_trgm
extension is enabled (it might already be):CREATE EXTENSION pg_trgm;
-
Exit the database prompt by typing
\q
and Enter. -
Verify the cluster is initialized with one node:
gitlab-ctl repmgr cluster show
The output should be similar to the following:
Role | Name | Upstream | Connection String ----------+----------|----------|---------------------------------------- * master | HOSTNAME | | host=HOSTNAME user=gitlab_repmgr dbname=gitlab_repmgr
-
Note down the hostname or IP address in the connection string:
host=HOSTNAME
. We will refer to the hostname in the next section as<primary_node_name>
. If the value is not an IP address, it will need to be a resolvable name (via DNS or/etc/hosts
)
SSH into the secondary node:
-
Set up the repmgr standby:
gitlab-ctl repmgr standby setup <primary_node_name>
Do note that this will remove the existing data on the node. The command has a wait time.
The output should be similar to the following:
Doing this will delete the entire contents of /var/opt/gitlab/postgresql/data If this is not what you want, hit Ctrl-C now to exit To skip waiting, rerun with the -w option Sleeping for 30 seconds Stopping the database Removing the data Cloning the data Starting the database Registering the node with the cluster ok: run: repmgrd: (pid 19068) 0s
Before moving on, make sure the databases are configured correctly. Run the following command on the primary node to verify that replication is working properly and the secondary nodes appear in the cluster:
gitlab-ctl repmgr cluster show
The output should be similar to the following:
Role | Name | Upstream | Connection String
----------+---------|-----------|------------------------------------------------
* master | MASTER | | host=<primary_node_name> user=gitlab_repmgr dbname=gitlab_repmgr
standby | STANDBY | MASTER | host=<secondary_node_name> user=gitlab_repmgr dbname=gitlab_repmgr
standby | STANDBY | MASTER | host=<secondary_node_name> user=gitlab_repmgr dbname=gitlab_repmgr
If the 'Role' column for any node says "FAILED", check the Troubleshooting section before proceeding.
Also, check that the repmgr-check-master
command works successfully on each node:
su - gitlab-consul
gitlab-ctl repmgr-check-master || echo 'This node is a standby repmgr node'
This command relies on exit codes to tell Consul whether a particular node is a master
or secondary. The most important thing here is that this command does not produce errors.
If there are errors it's most likely due to incorrect gitlab-consul
database user permissions.
Check the Troubleshooting section before proceeding.
Configure PgBouncer
Now that the PostgreSQL servers are all set up, let's configure PgBouncer. The following IPs will be used as an example:
10.6.0.31
: PgBouncer 110.6.0.32
: PgBouncer 210.6.0.33
: PgBouncer 3
-
On each PgBouncer node, edit
/etc/gitlab/gitlab.rb
, and replace<consul_password_hash>
and<pgbouncer_password_hash>
with the password hashes you set up previously:# Disable all components except Pgbouncer and Consul agent roles ['pgbouncer_role'] # Configure PgBouncer pgbouncer['admin_users'] = %w(pgbouncer gitlab-consul) pgbouncer['users'] = { 'gitlab-consul': { password: '<consul_password_hash>' }, 'pgbouncer': { password: '<pgbouncer_password_hash>' } } # Configure Consul agent consul['watchers'] = %w(postgresql) consul['enable'] = true consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13) } # Enable service discovery for Prometheus consul['monitoring_service_discovery'] = true # Set the network addresses that the exporters will listen on node_exporter['listen_address'] = '0.0.0.0:9100'
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure Omnibus GitLab for the changes to take effect.
NOTE: Note: If an error
execute[generate databases.ini]
occurs, this is due to an existing known issue. It will be resolved when you run a secondreconfigure
after the next step. -
Create a
.pgpass
file so Consul is able to reload PgBouncer. Enter the PgBouncer password twice when asked:gitlab-ctl write-pgpass --host 127.0.0.1 --database pgbouncer --user pgbouncer --hostuser gitlab-consul
-
Reconfigure GitLab once again to resolve any potential errors from the previous steps.
-
Ensure each node is talking to the current primary:
gitlab-ctl pgb-console # You will be prompted for PGBOUNCER_PASSWORD
-
Once the console prompt is available, run the following queries:
show databases ; show clients ;
The output should be similar to the following:
name | host | port | database | force_user | pool_size | reserve_pool | pool_mode | max_connections | current_connections ---------------------+-------------+------+---------------------+------------+-----------+--------------+-----------+-----------------+--------------------- gitlabhq_production | MASTER_HOST | 5432 | gitlabhq_production | | 20 | 0 | | 0 | 0 pgbouncer | | 6432 | pgbouncer | pgbouncer | 2 | 0 | statement | 0 | 0 (2 rows) type | user | database | state | addr | port | local_addr | local_port | connect_time | request_time | ptr | link | remote_pid | tls ------+-----------+---------------------+---------+----------------+-------+------------+------------+---------------------+---------------------+-----------+------+------------+----- C | pgbouncer | pgbouncer | active | 127.0.0.1 | 56846 | 127.0.0.1 | 6432 | 2017-08-21 18:09:59 | 2017-08-21 18:10:48 | 0x22b3880 | | 0 | (2 rows)
Configure the internal load balancer
If you're running more than one PgBouncer node as recommended, then at this time you'll need to set up a TCP internal load balancer to serve each correctly.
The following IP will be used as an example:
10.6.0.40
: Internal Load Balancer
Here's how you could do it with HAProxy:
global
log /dev/log local0
log localhost local1 notice
log stdout format raw local0
defaults
log global
default-server inter 10s fall 3 rise 2
balance leastconn
frontend internal-pgbouncer-tcp-in
bind *:6432
mode tcp
option tcplog
default_backend pgbouncer
backend pgbouncer
mode tcp
option tcp-check
server pgbouncer1 10.6.0.21:6432 check
server pgbouncer2 10.6.0.22:6432 check
server pgbouncer3 10.6.0.23:6432 check
Refer to your preferred Load Balancer's documentation for further guidance.
Configure Redis
Using Redis in scalable environment is possible using a Primary x Replica topology with a Redis Sentinel service to watch and automatically start the failover procedure.
Redis requires authentication if used with Sentinel. See Redis Security documentation for more information. We recommend using a combination of a Redis password and tight firewall rules to secure your Redis service. You are highly encouraged to read the Redis Sentinel documentation before configuring Redis with GitLab to fully understand the topology and architecture.
The requirements for a Redis setup are the following:
- All Redis nodes must be able to talk to each other and accept incoming
connections over Redis (
6379
) and Sentinel (26379
) ports (unless you change the default ones). - The server that hosts the GitLab application must be able to access the Redis nodes.
- Protect the nodes from access from external networks (Internet), using a firewall.
In this section, you'll be guided through configuring two external Redis clusters to be used with GitLab. The following IPs will be used as an example:
10.6.0.51
: Redis - Cache Primary10.6.0.52
: Redis - Cache Replica 110.6.0.53
: Redis - Cache Replica 210.6.0.71
: Sentinel - Cache 110.6.0.72
: Sentinel - Cache 210.6.0.73
: Sentinel - Cache 310.6.0.61
: Redis - Queues Primary10.6.0.62
: Redis - Queues Replica 110.6.0.63
: Redis - Queues Replica 210.6.0.81
: Sentinel - Queues 110.6.0.82
: Sentinel - Queues 210.6.0.83
: Sentinel - Queues 3
NOTE: Providing your own Redis instance: Managed Redis from cloud providers such as AWS ElastiCache will work. If these services support high availability, be sure it is not the Redis Cluster type. Redis version 5.0 or higher is required, as this is what ships with Omnibus GitLab packages starting with GitLab 13.0. Older Redis versions do not support an optional count argument to SPOP which is now required for Merge Trains. Note the Redis node's IP address or hostname, port, and password (if required). These will be necessary when configuring the GitLab application servers later.
Configure the Redis and Sentinel Cache cluster
This is the section where we install and set up the new Redis Cache instances.
NOTE: Note:
Redis nodes (both primary and replica) will need the same password defined in
redis['password']
. At any time during a failover the Sentinels can
reconfigure a node and change its status from primary to replica and vice versa.
Configure the primary Redis Cache node
-
SSH into the Primary Redis server.
-
Download/install the Omnibus GitLab package you want using steps 1 and 2 from the GitLab downloads page.
- Make sure you select the correct Omnibus package, with the same version and type (Community, Enterprise editions) of your current install.
- Do not complete any other steps on the download page.
-
Edit
/etc/gitlab/gitlab.rb
and add the contents:# Specify server role as 'redis_master_role' roles ['redis_master_role'] # IP address pointing to a local IP that the other machines can reach to. # You can also set bind to '0.0.0.0' which listen in all interfaces. # If you really need to bind to an external accessible IP, make # sure you add extra firewall rules to prevent unauthorized access. redis['bind'] = '10.6.0.51' # Define a port so Redis can listen for TCP requests which will allow other # machines to connect to it. redis['port'] = 6379 # Set up password authentication for Redis (use the same password in all nodes). redis['password'] = 'REDIS_PRIMARY_PASSWORD_OF_FIRST_CLUSTER' ## Enable service discovery for Prometheus consul['enable'] = true consul['monitoring_service_discovery'] = true ## The IPs of the Consul server nodes ## You can also use FQDNs and intermix them with IPs consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13), } # Set the network addresses that the exporters will listen on node_exporter['listen_address'] = '0.0.0.0:9100' redis_exporter['listen_address'] = '0.0.0.0:9121' # Prevent database migrations from running on upgrade gitlab_rails['auto_migrate'] = false
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure Omnibus GitLab for the changes to take effect.
NOTE: Note:
You can specify multiple roles like sentinel and Redis as:
roles ['redis_sentinel_role', 'redis_master_role']
.
Read more about roles.
Configure the replica Redis Cache nodes
-
SSH into the replica Redis server.
-
Download/install the Omnibus GitLab package you want using steps 1 and 2 from the GitLab downloads page.
- Make sure you select the correct Omnibus package, with the same version and type (Community, Enterprise editions) of your current install.
- Do not complete any other steps on the download page.
-
Edit
/etc/gitlab/gitlab.rb
and add the contents:# Specify server role as 'redis_replica_role' roles ['redis_replica_role'] # IP address pointing to a local IP that the other machines can reach to. # You can also set bind to '0.0.0.0' which listen in all interfaces. # If you really need to bind to an external accessible IP, make # sure you add extra firewall rules to prevent unauthorized access. redis['bind'] = '10.6.0.52' # Define a port so Redis can listen for TCP requests which will allow other # machines to connect to it. redis['port'] = 6379 # The same password for Redis authentication you set up for the primary node. redis['password'] = 'REDIS_PRIMARY_PASSWORD_OF_FIRST_CLUSTER' # The IP of the primary Redis node. redis['master_ip'] = '10.6.0.51' # Port of primary Redis server, uncomment to change to non default. Defaults # to `6379`. #redis['master_port'] = 6379 ## Enable service discovery for Prometheus consul['enable'] = true consul['monitoring_service_discovery'] = true ## The IPs of the Consul server nodes ## You can also use FQDNs and intermix them with IPs consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13), } # Set the network addresses that the exporters will listen on node_exporter['listen_address'] = '0.0.0.0:9100' redis_exporter['listen_address'] = '0.0.0.0:9121' # Prevent database migrations from running on upgrade gitlab_rails['auto_migrate'] = false
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure Omnibus GitLab for the changes to take effect.
-
Go through the steps again for all the other replica nodes, and make sure to set up the IPs correctly.
NOTE: Note:
You can specify multiple roles like sentinel and Redis as:
roles ['redis_sentinel_role', 'redis_master_role']
.
Read more about roles.
These values don't have to be changed again in /etc/gitlab/gitlab.rb
after
a failover, as the nodes will be managed by the Sentinels, and even after a
gitlab-ctl reconfigure
, they will get their configuration restored by
the same Sentinels.
Advanced configuration options are supported and can be added if needed.
Configure the Sentinel Cache nodes
NOTE: Note:
If you are using an external Redis Sentinel instance, be sure
to exclude the requirepass
parameter from the Sentinel
configuration. This parameter will cause clients to report NOAUTH Authentication required.
. Redis Sentinel 3.2.x does not support
password authentication.
Now that the Redis servers are all set up, let's configure the Sentinel servers. The following IPs will be used as an example:
10.6.0.71
: Sentinel - Cache 110.6.0.72
: Sentinel - Cache 210.6.0.73
: Sentinel - Cache 3
To configure the Sentinel Cache server:
-
SSH into the server that will host Consul/Sentinel.
-
Download/install the Omnibus GitLab Enterprise Edition package using steps 1 and 2 from the GitLab downloads page.
- Make sure you select the correct Omnibus package, with the same version the GitLab application is running.
- Do not complete any other steps on the download page.
-
Edit
/etc/gitlab/gitlab.rb
and add the contents:roles ['redis_sentinel_role'] ## Must be the same in every sentinel node redis['master_name'] = 'gitlab-redis-cache' ## The same password for Redis authentication you set up for the primary node. redis['master_password'] = 'REDIS_PRIMARY_PASSWORD_OF_FIRST_CLUSTER' ## The IP of the primary Redis node. redis['master_ip'] = '10.6.0.51' ## Define a port so Redis can listen for TCP requests which will allow other ## machines to connect to it. redis['port'] = 6379 ## Port of primary Redis server, uncomment to change to non default. Defaults ## to `6379`. #redis['master_port'] = 6379 ## Configure Sentinel's IP sentinel['bind'] = '10.6.0.71' ## Port that Sentinel listens on, uncomment to change to non default. Defaults ## to `26379`. #sentinel['port'] = 26379 ## Quorum must reflect the amount of voting sentinels it take to start a failover. ## Value must NOT be greater then the amount of sentinels. ## ## The quorum can be used to tune Sentinel in two ways: ## 1. If a the quorum is set to a value smaller than the majority of Sentinels ## we deploy, we are basically making Sentinel more sensible to primary failures, ## triggering a failover as soon as even just a minority of Sentinels is no longer ## able to talk with the primary. ## 1. If a quorum is set to a value greater than the majority of Sentinels, we are ## making Sentinel able to failover only when there are a very large number (larger ## than majority) of well connected Sentinels which agree about the primary being down.s sentinel['quorum'] = 2 ## Consider unresponsive server down after x amount of ms. #sentinel['down_after_milliseconds'] = 10000 ## Specifies the failover timeout in milliseconds. It is used in many ways: ## ## - The time needed to re-start a failover after a previous failover was ## already tried against the same primary by a given Sentinel, is two ## times the failover timeout. ## ## - The time needed for a replica replicating to a wrong primary according ## to a Sentinel current configuration, to be forced to replicate ## with the right primary, is exactly the failover timeout (counting since ## the moment a Sentinel detected the misconfiguration). ## ## - The time needed to cancel a failover that is already in progress but ## did not produced any configuration change (REPLICAOF NO ONE yet not ## acknowledged by the promoted replica). ## ## - The maximum time a failover in progress waits for all the replica to be ## reconfigured as replicas of the new primary. However even after this time ## the replicas will be reconfigured by the Sentinels anyway, but not with ## the exact parallel-syncs progression as specified. #sentinel['failover_timeout'] = 60000 ## Enable service discovery for Prometheus consul['enable'] = true consul['monitoring_service_discovery'] = true ## The IPs of the Consul server nodes ## You can also use FQDNs and intermix them with IPs consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13), } # Set the network addresses that the exporters will listen on node_exporter['listen_address'] = '0.0.0.0:9100' redis_exporter['listen_address'] = '0.0.0.0:9121' # Disable auto migrations gitlab_rails['auto_migrate'] = false
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure Omnibus GitLab for the changes to take effect.
-
Go through the steps again for all the other Consul/Sentinel nodes, and make sure you set up the correct IPs.
Configure the Redis and Sentinel Queues cluster
This is the section where we install and set up the new Redis Queues instances.
NOTE: Note:
Redis nodes (both primary and replica) will need the same password defined in
redis['password']
. At any time during a failover the Sentinels can
reconfigure a node and change its status from primary to replica and vice versa.
Configure the primary Redis Queues node
-
SSH into the Primary Redis server.
-
Download/install the Omnibus GitLab package you want using steps 1 and 2 from the GitLab downloads page.
- Make sure you select the correct Omnibus package, with the same version and type (Community, Enterprise editions) of your current install.
- Do not complete any other steps on the download page.
-
Edit
/etc/gitlab/gitlab.rb
and add the contents:# Specify server role as 'redis_master_role' roles ['redis_master_role'] # IP address pointing to a local IP that the other machines can reach to. # You can also set bind to '0.0.0.0' which listen in all interfaces. # If you really need to bind to an external accessible IP, make # sure you add extra firewall rules to prevent unauthorized access. redis['bind'] = '10.6.0.61' # Define a port so Redis can listen for TCP requests which will allow other # machines to connect to it. redis['port'] = 6379 # Set up password authentication for Redis (use the same password in all nodes). redis['password'] = 'REDIS_PRIMARY_PASSWORD_OF_SECOND_CLUSTER' ## Enable service discovery for Prometheus consul['enable'] = true consul['monitoring_service_discovery'] = true ## The IPs of the Consul server nodes ## You can also use FQDNs and intermix them with IPs consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13), } # Set the network addresses that the exporters will listen on node_exporter['listen_address'] = '0.0.0.0:9100' redis_exporter['listen_address'] = '0.0.0.0:9121'
-
Only the primary GitLab application server should handle migrations. To prevent database migrations from running on upgrade, add the following configuration to your
/etc/gitlab/gitlab.rb
file:gitlab_rails['auto_migrate'] = false
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure Omnibus GitLab for the changes to take effect.
NOTE: Note:
You can specify multiple roles like sentinel and Redis as:
roles ['redis_sentinel_role', 'redis_master_role']
.
Read more about roles.
Configure the replica Redis Queues nodes
-
SSH into the replica Redis Queue server.
-
Download/install the Omnibus GitLab package you want using steps 1 and 2 from the GitLab downloads page.
- Make sure you select the correct Omnibus package, with the same version and type (Community, Enterprise editions) of your current install.
- Do not complete any other steps on the download page.
-
Edit
/etc/gitlab/gitlab.rb
and add the contents:# Specify server role as 'redis_replica_role' roles ['redis_replica_role'] # IP address pointing to a local IP that the other machines can reach to. # You can also set bind to '0.0.0.0' which listen in all interfaces. # If you really need to bind to an external accessible IP, make # sure you add extra firewall rules to prevent unauthorized access. redis['bind'] = '10.6.0.62' # Define a port so Redis can listen for TCP requests which will allow other # machines to connect to it. redis['port'] = 6379 # The same password for Redis authentication you set up for the primary node. redis['password'] = 'REDIS_PRIMARY_PASSWORD_OF_SECOND_CLUSTER' # The IP of the primary Redis node. redis['master_ip'] = '10.6.0.61' # Port of primary Redis server, uncomment to change to non default. Defaults # to `6379`. #redis['master_port'] = 6379 ## Enable service discovery for Prometheus consul['enable'] = true consul['monitoring_service_discovery'] = true ## The IPs of the Consul server nodes ## You can also use FQDNs and intermix them with IPs consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13), } # Set the network addresses that the exporters will listen on node_exporter['listen_address'] = '0.0.0.0:9100' redis_exporter['listen_address'] = '0.0.0.0:9121' # Disable auto migrations gitlab_rails['auto_migrate'] = false
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure Omnibus GitLab for the changes to take effect.
-
Go through the steps again for all the other replica nodes, and make sure to set up the IPs correctly.
NOTE: Note:
You can specify multiple roles like sentinel and Redis as:
roles ['redis_sentinel_role', 'redis_master_role']
.
Read more about roles.
These values don't have to be changed again in /etc/gitlab/gitlab.rb
after
a failover, as the nodes will be managed by the Sentinels, and even after a
gitlab-ctl reconfigure
, they will get their configuration restored by
the same Sentinels.
Advanced configuration options are supported and can be added if needed.
Configure the Sentinel Queues nodes
NOTE: Note:
If you are using an external Redis Sentinel instance, be sure
to exclude the requirepass
parameter from the Sentinel
configuration. This parameter will cause clients to report NOAUTH Authentication required.
. Redis Sentinel 3.2.x does not support
password authentication.
Now that the Redis servers are all set up, let's configure the Sentinel servers. The following IPs will be used as an example:
10.6.0.81
: Sentinel - Queues 110.6.0.82
: Sentinel - Queues 210.6.0.83
: Sentinel - Queues 3
To configure the Sentinel Queues server:
-
SSH into the server that will host Sentinel.
-
Download/install the Omnibus GitLab Enterprise Edition package using steps 1 and 2 from the GitLab downloads page.
- Make sure you select the correct Omnibus package, with the same version the GitLab application is running.
- Do not complete any other steps on the download page.
-
Edit
/etc/gitlab/gitlab.rb
and add the contents:roles ['redis_sentinel_role'] ## Must be the same in every sentinel node redis['master_name'] = 'gitlab-redis-persistent' ## The same password for Redis authentication you set up for the primary node. redis['master_password'] = 'REDIS_PRIMARY_PASSWORD_OF_SECOND_CLUSTER' ## The IP of the primary Redis node. redis['master_ip'] = '10.6.0.61' ## Define a port so Redis can listen for TCP requests which will allow other ## machines to connect to it. redis['port'] = 6379 ## Port of primary Redis server, uncomment to change to non default. Defaults ## to `6379`. #redis['master_port'] = 6379 ## Configure Sentinel's IP sentinel['bind'] = '10.6.0.81' ## Port that Sentinel listens on, uncomment to change to non default. Defaults ## to `26379`. #sentinel['port'] = 26379 ## Quorum must reflect the amount of voting sentinels it take to start a failover. ## Value must NOT be greater then the amount of sentinels. ## ## The quorum can be used to tune Sentinel in two ways: ## 1. If a the quorum is set to a value smaller than the majority of Sentinels ## we deploy, we are basically making Sentinel more sensible to primary failures, ## triggering a failover as soon as even just a minority of Sentinels is no longer ## able to talk with the primary. ## 1. If a quorum is set to a value greater than the majority of Sentinels, we are ## making Sentinel able to failover only when there are a very large number (larger ## than majority) of well connected Sentinels which agree about the primary being down.s sentinel['quorum'] = 2 ## Consider unresponsive server down after x amount of ms. #sentinel['down_after_milliseconds'] = 10000 ## Specifies the failover timeout in milliseconds. It is used in many ways: ## ## - The time needed to re-start a failover after a previous failover was ## already tried against the same primary by a given Sentinel, is two ## times the failover timeout. ## ## - The time needed for a replica replicating to a wrong primary according ## to a Sentinel current configuration, to be forced to replicate ## with the right primary, is exactly the failover timeout (counting since ## the moment a Sentinel detected the misconfiguration). ## ## - The time needed to cancel a failover that is already in progress but ## did not produced any configuration change (REPLICAOF NO ONE yet not ## acknowledged by the promoted replica). ## ## - The maximum time a failover in progress waits for all the replica to be ## reconfigured as replicas of the new primary. However even after this time ## the replicas will be reconfigured by the Sentinels anyway, but not with ## the exact parallel-syncs progression as specified. #sentinel['failover_timeout'] = 60000 ## Enable service discovery for Prometheus consul['enable'] = true consul['monitoring_service_discovery'] = true ## The IPs of the Consul server nodes ## You can also use FQDNs and intermix them with IPs consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13), } # Set the network addresses that the exporters will listen on node_exporter['listen_address'] = '0.0.0.0:9100' redis_exporter['listen_address'] = '0.0.0.0:9121' # Disable auto migrations gitlab_rails['auto_migrate'] = false
-
To prevent database migrations from running on upgrade, run:
sudo touch /etc/gitlab/skip-auto-reconfigure
Only the primary GitLab application server should handle migrations.
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure Omnibus GitLab for the changes to take effect.
-
Go through the steps again for all the other Sentinel nodes, and make sure you set up the correct IPs.
Configure Gitaly
Deploying Gitaly in its own server can benefit GitLab installations that are larger than a single machine.
The Gitaly node requirements are dependent on customer data, specifically the number of
projects and their repository sizes. Two nodes are recommended as an absolute minimum.
Each Gitaly node should store no more than 5TB of data and have the number of
gitaly-ruby
workers set to 20% of available CPUs.
Additional nodes should be considered in conjunction with a review of expected
data size and spread based on the recommendations above.
It is also strongly recommended that all Gitaly nodes be set up with SSD disks with a throughput of at least 8,000 IOPS for read operations and 2,000 IOPS for write, as Gitaly has heavy I/O. These IOPS values are recommended only as a starter as with time they may be adjusted higher or lower depending on the scale of your environment's workload. If you're running the environment on a Cloud provider, you may need to refer to their documentation on how to configure IOPS correctly.
Some things to note:
- The GitLab Rails application shards repositories into repository storages.
- A Gitaly server can host one or more storages.
- A GitLab server can use one or more Gitaly servers.
- Gitaly addresses must be specified in such a way that they resolve correctly for ALL Gitaly clients.
- Gitaly servers must not be exposed to the public internet, as Gitaly's network traffic is unencrypted by default. The use of a firewall is highly recommended to restrict access to the Gitaly server. Another option is to use TLS.
TIP: Tip: For more information about Gitaly's history and network architecture see the standalone Gitaly documentation.
Note: Note: The token referred to throughout the Gitaly documentation is just an arbitrary password selected by the administrator. It is unrelated to tokens created for the GitLab API or other similar web API tokens.
Below we describe how to configure two Gitaly servers, with IPs and domain names:
10.6.0.91
: Gitaly 1 (gitaly1.internal
)10.6.0.92
: Gitaly 2 (gitaly2.internal
)
The secret token is assumed to be gitalysecret
and that
your GitLab installation has three repository storages:
default
on Gitaly 1storage1
on Gitaly 1storage2
on Gitaly 2
On each node:
-
Download/Install the Omnibus GitLab package you want using steps 1 and 2 from the GitLab downloads page but without providing the
EXTERNAL_URL
value. -
Edit
/etc/gitlab/gitlab.rb
to configure storage paths, enable the network listener and configure the token:# /etc/gitlab/gitlab.rb # Gitaly and GitLab use two shared secrets for authentication, one to authenticate gRPC requests # to Gitaly, and a second for authentication callbacks from GitLab-Shell to the GitLab internal API. # The following two values must be the same as their respective values # of the GitLab Rails application setup gitaly['auth_token'] = 'gitalysecret' gitlab_shell['secret_token'] = 'shellsecret' # Avoid running unnecessary services on the Gitaly server postgresql['enable'] = false redis['enable'] = false nginx['enable'] = false puma['enable'] = false unicorn['enable'] = false sidekiq['enable'] = false gitlab_workhorse['enable'] = false grafana['enable'] = false # If you run a separate monitoring node you can disable these services alertmanager['enable'] = false prometheus['enable'] = false # Prevent database connections during 'gitlab-ctl reconfigure' gitlab_rails['rake_cache_clear'] = false gitlab_rails['auto_migrate'] = false # Configure the gitlab-shell API callback URL. Without this, `git push` will # fail. This can be your 'front door' GitLab URL or an internal load # balancer. # Don't forget to copy `/etc/gitlab/gitlab-secrets.json` from web server to Gitaly server. gitlab_rails['internal_api_url'] = 'https://gitlab.example.com' # Make Gitaly accept connections on all network interfaces. You must use # firewalls to restrict access to this address/port. # Comment out following line if you only want to support TLS connections gitaly['listen_addr'] = "0.0.0.0:8075"
-
Append the following to
/etc/gitlab/gitlab.rb
for each respective server:-
On
gitaly1.internal
:git_data_dirs({ 'default' => { 'path' => '/var/opt/gitlab/git-data' }, 'storage1' => { 'path' => '/mnt/gitlab/git-data' }, })
-
On
gitaly2.internal
:git_data_dirs({ 'storage2' => { 'path' => '/mnt/gitlab/git-data' }, })
-
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Save the file and reconfigure GitLab.
Gitaly TLS support
Gitaly supports TLS encryption. To be able to communicate
with a Gitaly instance that listens for secure connections you will need to use tls://
URL
scheme in the gitaly_address
of the corresponding storage entry in the GitLab configuration.
You will need to bring your own certificates as this isn't provided automatically. The certificate, or its certificate authority, must be installed on all Gitaly nodes (including the Gitaly node using the certificate) and on all client nodes that communicate with it following the procedure described in GitLab custom certificate configuration.
NOTE: Note: The self-signed certificate must specify the address you use to access the Gitaly server. If you are addressing the Gitaly server by a hostname, you can either use the Common Name field for this, or add it as a Subject Alternative Name. If you are addressing the Gitaly server by its IP address, you must add it as a Subject Alternative Name to the certificate. gRPC does not support using an IP address as Common Name in a certificate.
NOTE: Note:
It is possible to configure Gitaly servers with both an
unencrypted listening address listen_addr
and an encrypted listening
address tls_listen_addr
at the same time. This allows you to do a
gradual transition from unencrypted to encrypted traffic, if necessary.
To configure Gitaly with TLS:
-
Create the
/etc/gitlab/ssl
directory and copy your key and certificate there:sudo mkdir -p /etc/gitlab/ssl sudo chmod 755 /etc/gitlab/ssl sudo cp key.pem cert.pem /etc/gitlab/ssl/ sudo chmod 644 key.pem cert.pem
-
Copy the cert to
/etc/gitlab/trusted-certs
so Gitaly will trust the cert when calling into itself:sudo cp /etc/gitlab/ssl/cert.pem /etc/gitlab/trusted-certs/
-
Edit
/etc/gitlab/gitlab.rb
and add:gitaly['tls_listen_addr'] = "0.0.0.0:9999" gitaly['certificate_path'] = "/etc/gitlab/ssl/cert.pem" gitaly['key_path'] = "/etc/gitlab/ssl/key.pem"
-
Delete
gitaly['listen_addr']
to allow only encrypted connections. -
Save the file and reconfigure GitLab.
Configure Sidekiq
Sidekiq requires connections to the Redis, PostgreSQL and Gitaly instances. The following IPs will be used as an example:
10.6.0.101
: Sidekiq 110.6.0.102
: Sidekiq 210.6.0.103
: Sidekiq 310.6.0.104
: Sidekiq 4
To configure the Sidekiq nodes, on each one:
-
SSH into the Sidekiq server.
-
Download/install the Omnibus GitLab package you want using steps 1 and 2 from the GitLab downloads page. Do not complete any other steps on the download page.
-
Open
/etc/gitlab/gitlab.rb
with your editor:######################################## ##### Services Disabled ### ######################################## nginx['enable'] = false grafana['enable'] = false prometheus['enable'] = false alertmanager['enable'] = false gitaly['enable'] = false gitlab_workhorse['enable'] = false nginx['enable'] = false puma['enable'] = false postgres_exporter['enable'] = false postgresql['enable'] = false redis['enable'] = false redis_exporter['enable'] = false gitlab_exporter['enable'] = false ######################################## #### Redis ### ######################################## ## Redis connection details ## First cluster that will host the cache gitlab_rails['redis_cache_instance'] = 'redis://:<REDIS_PRIMARY_PASSWORD_OF_FIRST_CLUSTER>@gitlab-redis-cache' gitlab_rails['redis_cache_sentinels'] = [ {host: '10.6.0.71', port: 26379}, {host: '10.6.0.72', port: 26379}, {host: '10.6.0.73', port: 26379}, ] ## Second cluster that will host the queues, shared state, and actioncable gitlab_rails['redis_queues_instance'] = 'redis://:<REDIS_PRIMARY_PASSWORD_OF_SECOND_CLUSTER>@gitlab-redis-persistent' gitlab_rails['redis_shared_state_instance'] = 'redis://:<REDIS_PRIMARY_PASSWORD_OF_SECOND_CLUSTER>@gitlab-redis-persistent' gitlab_rails['redis_actioncable_instance'] = 'redis://:<REDIS_PRIMARY_PASSWORD_OF_SECOND_CLUSTER>@gitlab-redis-persistent' gitlab_rails['redis_queues_sentinels'] = [ {host: '10.6.0.81', port: 26379}, {host: '10.6.0.82', port: 26379}, {host: '10.6.0.83', port: 26379}, ] gitlab_rails['redis_shared_state_sentinels'] = [ {host: '10.6.0.81', port: 26379}, {host: '10.6.0.82', port: 26379}, {host: '10.6.0.83', port: 26379}, ] gitlab_rails['redis_actioncable_sentinels'] = [ {host: '10.6.0.81', port: 26379}, {host: '10.6.0.82', port: 26379}, {host: '10.6.0.83', port: 26379}, ] ####################################### ### Gitaly ### ####################################### git_data_dirs({ 'default' => { 'gitaly_address' => 'tcp://gitaly1.internal:8075' }, 'storage1' => { 'gitaly_address' => 'tcp://gitaly1.internal:8075' }, 'storage2' => { 'gitaly_address' => 'tcp://gitaly2.internal:8075' }, }) gitlab_rails['gitaly_token'] = 'YOUR_TOKEN' ####################################### ### Postgres ### ####################################### gitlab_rails['db_host'] = '10.6.0.20' # internal load balancer IP gitlab_rails['db_port'] = 6432 gitlab_rails['db_password'] = '<postgresql_user_password>' gitlab_rails['db_adapter'] = 'postgresql' gitlab_rails['db_encoding'] = 'unicode' gitlab_rails['auto_migrate'] = false ####################################### ### Sidekiq configuration ### ####################################### sidekiq['listen_address'] = "0.0.0.0" sidekiq['cluster'] = true # no need to set this after GitLab 13.0 ####################################### ### Monitoring configuration ### ####################################### consul['enable'] = true consul['monitoring_service_discovery'] = true consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13) } # Set the network addresses that the exporters will listen on node_exporter['listen_address'] = '0.0.0.0:9100' # Rails Status for prometheus gitlab_rails['monitoring_whitelist'] = ['10.6.0.121/32', '127.0.0.0/8']
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Reconfigure GitLab for the changes to take effect.
TIP: Tip: You can also run multiple Sidekiq processes.
Configure GitLab Rails
NOTE: Note: In our architectures we run each GitLab Rails node using the Puma webserver and have its number of workers set to 90% of available CPUs along with four threads. For nodes that are running Rails with other components the worker value should be reduced accordingly where we've found 50% achieves a good balance but this is dependent on workload.
This section describes how to configure the GitLab application (Rails) component.
The following IPs will be used as an example:
10.6.0.111
: GitLab application 110.6.0.112
: GitLab application 210.6.0.113
: GitLab application 3
On each node perform the following:
-
Download/install Omnibus GitLab using steps 1 and 2 from GitLab downloads. Do not complete other steps on the download page.
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Edit
/etc/gitlab/gitlab.rb
and use the following configuration. To maintain uniformity of links across nodes, theexternal_url
on the application server should point to the external URL that users will use to access GitLab. This would be the URL of the external load balancer which will route traffic to the GitLab application server:external_url 'https://gitlab.example.com' # Gitaly and GitLab use two shared secrets for authentication, one to authenticate gRPC requests # to Gitaly, and a second for authentication callbacks from GitLab-Shell to the GitLab internal API. # The following two values must be the same as their respective values # of the Gitaly setup gitlab_rails['gitaly_token'] = 'gitalysecret' gitlab_shell['secret_token'] = 'shellsecret' git_data_dirs({ 'default' => { 'gitaly_address' => 'tcp://gitaly1.internal:8075' }, 'storage1' => { 'gitaly_address' => 'tcp://gitaly1.internal:8075' }, 'storage2' => { 'gitaly_address' => 'tcp://gitaly2.internal:8075' }, }) ## Disable components that will not be on the GitLab application server roles ['application_role'] gitaly['enable'] = false nginx['enable'] = true sidekiq['enable'] = false ## PostgreSQL connection details # Disable PostgreSQL on the application node postgresql['enable'] = false gitlab_rails['db_host'] = '10.6.0.20' # internal load balancer IP gitlab_rails['db_port'] = 6432 gitlab_rails['db_password'] = '<postgresql_user_password>' gitlab_rails['auto_migrate'] = false ## Redis connection details ## First cluster that will host the cache gitlab_rails['redis_cache_instance'] = 'redis://:<REDIS_PRIMARY_PASSWORD_OF_FIRST_CLUSTER>@gitlab-redis-cache' gitlab_rails['redis_cache_sentinels'] = [ {host: '10.6.0.71', port: 26379}, {host: '10.6.0.72', port: 26379}, {host: '10.6.0.73', port: 26379}, ] ## Second cluster that will host the queues, shared state, and actionable gitlab_rails['redis_queues_instance'] = 'redis://:<REDIS_PRIMARY_PASSWORD_OF_SECOND_CLUSTER>@gitlab-redis-persistent' gitlab_rails['redis_shared_state_instance'] = 'redis://:<REDIS_PRIMARY_PASSWORD_OF_SECOND_CLUSTER>@gitlab-redis-persistent' gitlab_rails['redis_actioncable_instance'] = 'redis://:<REDIS_PRIMARY_PASSWORD_OF_SECOND_CLUSTER>@gitlab-redis-persistent' gitlab_rails['redis_queues_sentinels'] = [ {host: '10.6.0.81', port: 26379}, {host: '10.6.0.82', port: 26379}, {host: '10.6.0.83', port: 26379}, ] gitlab_rails['redis_shared_state_sentinels'] = [ {host: '10.6.0.81', port: 26379}, {host: '10.6.0.82', port: 26379}, {host: '10.6.0.83', port: 26379}, ] gitlab_rails['redis_actioncable_sentinels'] = [ {host: '10.6.0.81', port: 26379}, {host: '10.6.0.82', port: 26379}, {host: '10.6.0.83', port: 26379}, ] # Set the network addresses that the exporters used for monitoring will listen on node_exporter['listen_address'] = '0.0.0.0:9100' gitlab_workhorse['prometheus_listen_addr'] = '0.0.0.0:9229' puma['listen'] = '0.0.0.0' # Add the monitoring node's IP address to the monitoring whitelist and allow it to # scrape the NGINX metrics gitlab_rails['monitoring_whitelist'] = ['10.6.0.121/32', '127.0.0.0/8'] nginx['status']['options']['allow'] = ['10.6.0.121/32', '127.0.0.0/8']
-
Save the file and reconfigure GitLab.
-
If you're using Gitaly with TLS support, make sure the
git_data_dirs
entry is configured withtls
instead oftcp
:git_data_dirs({ 'default' => { 'gitaly_address' => 'tls://gitaly1.internal:9999' }, 'storage1' => { 'gitaly_address' => 'tls://gitaly1.internal:9999' }, 'storage2' => { 'gitaly_address' => 'tls://gitaly2.internal:9999' }, })
-
Copy the cert into
/etc/gitlab/trusted-certs
:sudo cp cert.pem /etc/gitlab/trusted-certs/
-
-
If you're using NFS:
-
If necessary, install the NFS client utility packages using the following commands:
# Ubuntu/Debian apt-get install nfs-common # CentOS/Red Hat yum install nfs-utils nfs-utils-lib
-
Specify the necessary NFS mounts in
/etc/fstab
. The exact contents of/etc/fstab
will depend on how you chose to configure your NFS server. See the NFS documentation for examples and the various options. -
Create the shared directories. These may be different depending on your NFS mount locations.
mkdir -p /var/opt/gitlab/.ssh /var/opt/gitlab/gitlab-rails/uploads /var/opt/gitlab/gitlab-rails/shared /var/opt/gitlab/gitlab-ci/builds /var/opt/gitlab/git-data
-
Edit
/etc/gitlab/gitlab.rb
and use the following configuration:## Prevent GitLab from starting if NFS data mounts are not available high_availability['mountpoint'] = '/var/opt/gitlab/git-data' ## Ensure UIDs and GIDs match between servers for permissions via NFS user['uid'] = 9000 user['gid'] = 9000 web_server['uid'] = 9001 web_server['gid'] = 9001 registry['uid'] = 9002 registry['gid'] = 9002
-
-
Save the file and reconfigure GitLab.
-
Confirm the node can connect to Gitaly:
sudo gitlab-rake gitlab:gitaly:check
Then, tail the logs to see the requests:
sudo gitlab-ctl tail gitaly
-
Optionally, from the Gitaly servers, confirm that Gitaly can perform callbacks to the internal API:
sudo /opt/gitlab/embedded/service/gitlab-shell/bin/check -config /opt/gitlab/embedded/service/gitlab-shell/config.yml
NOTE: Note:
When you specify https
in the external_url
, as in the example
above, GitLab assumes you have SSL certificates in /etc/gitlab/ssl/
. If
certificates are not present, NGINX will fail to start. See the
NGINX documentation
for more information.
GitLab Rails post-configuration
-
Designate one application node for running database migrations during installation and updates. Initialize the GitLab database and ensure all migrations ran:
sudo gitlab-rake gitlab:db:configure
NOTE: Note: If you encounter a
rake aborted!
error stating that PgBouncer is failing to connect to PostgreSQL it may be that your PgBouncer node's IP address is missing from PostgreSQL'strust_auth_cidr_addresses
ingitlab.rb
on your database nodes. See PgBouncer errorERROR: pgbouncer cannot connect to server
in the Troubleshooting section before proceeding. -
Configure fast lookup of authorized SSH keys in the database.
Configure Prometheus
The Omnibus GitLab package can be used to configure a standalone Monitoring node running Prometheus and Grafana.
The following IP will be used as an example:
10.6.0.121
: Prometheus
To configure the Monitoring node:
-
SSH into the Monitoring node.
-
Download/install the Omnibus GitLab package you want using steps 1 and 2 from the GitLab downloads page. Do not complete any other steps on the download page.
-
Copy the
/etc/gitlab/gitlab-secrets.json
file from your Consul server, and replace the file of the same name on this server. If that file is not on this server, add the file from your Consul server to this server. -
Edit
/etc/gitlab/gitlab.rb
and add the contents:external_url 'http://gitlab.example.com' # Disable all other services gitlab_rails['auto_migrate'] = false alertmanager['enable'] = false gitaly['enable'] = false gitlab_exporter['enable'] = false gitlab_workhorse['enable'] = false nginx['enable'] = true postgres_exporter['enable'] = false postgresql['enable'] = false redis['enable'] = false redis_exporter['enable'] = false sidekiq['enable'] = false puma['enable'] = false unicorn['enable'] = false node_exporter['enable'] = false gitlab_exporter['enable'] = false # Enable Prometheus prometheus['enable'] = true prometheus['listen_address'] = '0.0.0.0:9090' prometheus['monitor_kubernetes'] = false # Enable Login form grafana['disable_login_form'] = false # Enable Grafana grafana['enable'] = true grafana['admin_password'] = '<grafana_password>' # Enable service discovery for Prometheus consul['enable'] = true consul['monitoring_service_discovery'] = true consul['configuration'] = { retry_join: %w(10.6.0.11 10.6.0.12 10.6.0.13) }
-
Save the file and reconfigure GitLab.
-
In the GitLab UI, set
admin/application_settings/metrics_and_profiling
> Metrics - Grafana to/-/grafana
tohttp[s]://<MONITOR NODE>/-/grafana
Configure the object storage
GitLab supports using an object storage service for holding numerous types of data. It's recommended over NFS and in general it's better in larger setups as object storage is typically much more performant, reliable, and scalable.
Object storage options that GitLab has tested, or is aware of customers using include:
- SaaS/Cloud solutions such as Amazon S3, Google cloud storage.
- On-premises hardware and appliances from various storage vendors.
- MinIO. There is a guide to deploying this within our Helm Chart documentation.
For configuring GitLab to use Object Storage refer to the following guides based on what features you intend to use:
- Configure object storage for backups.
- Configure object storage for job artifacts including incremental logging.
- Configure object storage for LFS objects.
- Configure object storage for uploads.
- Configure object storage for merge request diffs.
- Configure object storage for Container Registry (optional feature).
- Configure object storage for Mattermost (optional feature).
- Configure object storage for packages (optional feature). (PREMIUM ONLY)
- Configure object storage for Dependency Proxy (optional feature). (PREMIUM ONLY)
- Configure object storage for Pseudonymizer (optional feature). (ULTIMATE ONLY)
- Configure object storage for autoscale runner caching (optional - for improved performance).
- Configure object storage for Terraform state files.
Using separate buckets for each data type is the recommended approach for GitLab.
A limitation of our configuration is that each use of object storage is separately configured. We have an issue for improving this and easily using one bucket with separate folders is one improvement that this might bring.
There is at least one specific issue with using the same bucket: when GitLab is deployed with the Helm chart restore from backup will not properly function unless separate buckets are used.
One risk of using a single bucket would be if your organization decided to migrate GitLab to the Helm deployment in the future. GitLab would run, but the situation with backups might not be realized until the organization had a critical requirement for the backups to work.
Configure Advanced Search (STARTER ONLY)
NOTE: Note: Elasticsearch cluster design and requirements are dependent on your specific data. For recommended best practices on how to set up your Elasticsearch cluster alongside your instance, read how to choose the optimal cluster configuration.
You can leverage Elasticsearch and enable Advanced Search for faster, more advanced code search across your entire GitLab instance.
Configure NFS (optional)
Object storage, along with Gitaly are recommended over NFS wherever possible for improved performance. If you intend to use GitLab Pages, this currently requires NFS.
See how to configure NFS.
Troubleshooting
See the troubleshooting documentation.